pix facebook
Enolgas Valvole Acqua Raccordi

Axo Pe Plastic

Fitting for plastic polyethylene pipe and O-ring

Axo Pe Plastic guarantees extremely reliable performance. Among the main features: abundant guide depth of the pipe in the body, useful for obliquely cut pipes, double seal with locking by means of the pipe clamp cone and through an O-ring compressed by the special ring, extremely simple assembly and disassembly.

Material specification

Approved to EN 1254

Enolgas Axo Pe Plastic caratteristiche

   

COMPONENT

MATERIAL

  1 NUT CW 617 N UNI EN 12165
  2 PIPE GRIP CONE TECHNOPOLYMER
  3 THRUST RING TECHNOPOLYMER
  4 O-RING ELASTOMER
  5 PRESSURE CONE* CW 614 N UNI EN 12164
  6 BODY CW 617 N UNI EN 12165

* OPTIONAL (on request)


Characteristics

ASSEMBLY INSTRUCTIONS

In order to assemble AXO PE PLASTIC, carry out the following operations in the following priority:

  1. Cut the PE-pipe vertically, then trim flashes
  2. Put on the pipe, respectively: the nut (part 1), the pipe grip cone (part 2) and the thrust ring (part 3). Leave the o-ring (part 4) in the body.
  3. Insert the pressure cone (part 5)  into the pipe until it stops.
  4. Insert the pipe into the body (part 6) until it stops.
  5. Approach manually the single components (parts 3 and 2) to the body (part 6) and then approach and screw the nut (part 1) tight.
NOTE In order to make the assembly easier, the pipeshouldn’t be excessively oval. According to UNI EN 13828 in presence of water which could be aggressive for brass alloy, as agree with UNI EN ISO 6509 standard, is necessary the DZR brass alloy. The manufacture is available on request.
AXO PE The pipe grip cone and the thrust ring are in CW 614 N UNI EN 12164 brass.
FEATURES Deep guideway for the pipe in the body (part 6) which allows a proper housing of diagonally cut  pipes too. Perfect seal of the pipe thanks to the pipe grip cone (part 2) whose jaws grip the pipe firmly without breaking it. Extremely simple and quick assembly and disassembly by screwing and unscrewing the nut (part 1). Perfect tightness thanks to the o-ring (part 4) which adheres to the external diameter of the pipe. Accurate and solid design for high and reliable performances.
DOUBLE SEAL The seal of the fitting and the tightness of the pipe are obtained by means of two different elements.
The seal is guaranteed by a tapered gasket in elastomer.
The tightness of the pipe is instead assured by the pipe grip cone, whose jaws grip the pipe when the nut is screwed tight.
END CONNECTIONS Ends are ISO 228/1 threaded.
WORKING PRESSURE PN 16 max.(with water).
USES The fittings are suitable for connecting the following types of polyethylene pipes:
Polyethylene type 312 high density UNI 7611-7615 (PN 2,5 – PN 4 – PN 6 – PN 10 – PN 16).
Polyethylene type 316 high density UNI ISO 4437.
Polyethylene type 312 low density UNI 7990-7991 (PN 4 – PN 6 – PN 10).
AXO PE fitting is recommended for use with water, air and inert gas.
IMPORTANT NOTE AXO PE fitting shall not be used for use with domestic fuel gas applications according to the standard UNI-CIG 7129 in Italy or others valid in your country. 
TEMPERATURE LIMITS From -20°C to +90°C

 

Enolgas Axo Pe Plastic caratteristiche

Pressure/temperature diagram

 

Download
Axo Pe Plastic 749.86 KB
  • C0300

    AXO PE PLASTIC
    Straight fitting for PE-pipe, female, sandblasted.
    EAC
  • C0302

    AXO PE PLASTIC
    Straight fitting for PE-pipe, male, sandblasted.
    EAC
  • C0304

    AXO PE PLASTIC
    Straight double fitting for PE-pipe, sandblasted
    EAC
  • C0306

    AXO PE PLASTIC
    Angled fitting for PE-pipe, female, sandblasted.
    EAC
  • C0308

    AXO PE PLASTIC
    Angled fitting for PE-pipe, male, sandblasted.
    EAC
  • C0310

    AXO PE PLASTIC
    Angled double fitting for PE-pipe, sandblasted.
    EAC
  • C0312

    AXO PE PLASTIC
    T-fitting for PE-pipe, female, sandblasted.
    EAC
  • C0316

    AXO PE PLASTIC
    EAC